Fabric Care & Lifestyle

How to get blood stains out of fabric at home

A woman in a laundry facility standing by a washing machine, contemplating the process.

Photo by Tima Miroshnichenko on Pexels

Blood stains on fabric are surprisingly fixable, but only if you understand the one rule that changes everything: cold water only. Heat sets a blood stain permanently, and that includes warm water from the tap, a hot wash cycle, or an iron. Work cold from start to finish and most blood stains, fresh or dried, will come out.

Why blood stains behave differently to other stains

Blood contains haemoglobin, a protein that bonds to fabric fibres when exposed to heat. Fresh blood is water-soluble and rinses out easily. Once that protein dries and bonds, it takes more than water to lift it. Knowing this explains why the treatment differs depending on how old the stain is, and why doing nothing is always worse than acting quickly.

The fabric type also matters. Printed cotton and jersey respond well to most treatments. Delicate fabrics like modal or silk need a gentler approach. If you're working on a printed fabric, understanding fabric colour fastness first will help you choose a treatment that removes the stain without lifting the print.

How to treat a fresh blood stain

Speed matters here. The quicker you act, the less the protein has bonded.

  1. Rinse immediately under cold running water. Hold the fabric with the stained side facing the tap so the water pushes the stain out rather than through the fibres. Run cold water for at least 60 seconds.
  2. Apply salt. For small or stubborn spots after rinsing, pour a generous amount of table salt directly onto the wet stain and gently rub with your fingers. Salt draws moisture and blood out of the fibres. Leave it for 5 minutes, then rinse cold again.
  3. Use dish soap or hand soap. A drop of regular liquid dish soap worked into the stain with cold water will tackle any remaining residue. Rinse thoroughly.
  4. Check before drying. Never put the fabric in a dryer or iron it until you're certain the stain is gone. Even a trace of stain will set permanently under heat.

How to treat a dried blood stain

Dried blood is a tougher challenge but not an impossible one. Rehydrating the stain is the key first step.

Soak the stained area in cold water for 30 minutes. This softens the dried protein and makes it easier to lift. After soaking, apply one of the following treatments.

  • Hydrogen peroxide (3%): Apply a small amount directly to the stain and watch it fizz. The bubbling action lifts the protein from the fibres. Blot, don't rub. Rinse with cold water. Test a hidden area first on printed or dark fabrics, as hydrogen peroxide can lighten some dyes.
  • Enzyme-based stain remover: Products like Preen or Vanish Oxi Action contain enzymes specifically designed to break down protein-based stains. Apply to the damp stain, leave for the time stated on the packaging, then rinse cold.
  • Bicarbonate of soda paste: Mix bicarb with cold water into a thick paste, spread it over the stain, leave for 30 minutes, then rinse. Gentler than hydrogen peroxide and safe on most prints.

For very stubborn dried stains, repeat the treatment rather than increasing the chemical concentration. Two gentle rounds beat one aggressive one, particularly on custom printed fabric where the dye layer is part of the surface.

What not to do

A few common instincts make blood stains worse. Avoid all of these.

  • Hot water at any stage, including a warm rinse after treatment.
  • Rubbing aggressively. It spreads the stain and pushes it deeper into the weave.
  • Putting the item in the dryer before the stain is fully gone.
  • Using bleach on printed fabrics. It strips colour indiscriminately.

Ironing over a treated but not fully removed stain is a particularly easy mistake to make. It's worth re-reading how to iron printed fabric without ruining the design before you pick up the iron post-treatment, especially if you're working with a digitally printed piece.

Specific fabric considerations

Printed cotton and cotton jersey handle most of the treatments above without issue. Wash them on a cold, gentle cycle after treatment and air dry.

Linen and canvas tolerate hydrogen peroxide well and benefit from an extended cold soak before treatment. Modal and bamboo fabrics are more sensitive. Stick to the bicarb paste method or a mild enzyme cleaner, and handle them gently throughout.

For anything dry-clean only, blot the excess with cold water and take the item to a professional as soon as possible. Mention that the stain is blood so the cleaner can use the right treatment.

After the stain is gone: washing and drying

Once the stain has lifted fully, machine wash the item on a cold or cool cycle with a standard detergent. Skip the fabric softener on this wash. It's also worth checking the care label before washing, since the wrong cycle can undo all your work. If you're not confident reading care symbols, the guide on how to read fabric care labels covers every symbol you'll encounter.

Air dry the item flat or on a hanger. Keep it out of direct sunlight until you're certain the stain is gone, as UV exposure can yellow treated areas on some white or pale fabrics. Once fully dry and stain-free, it's safe to iron or store as normal.

When home treatment won't be enough

Some stains are simply too old, too large, or set into a fabric that can't tolerate treatment at home. If you've attempted the steps above twice without improvement, a professional laundryor dry cleaner is the right call. The cost of professional treatment is almost always less than replacing a piece you made yourself or ordered as a custom print.

Acting fast, working cold, and choosing the right method for the stain's age are the three things that determine whether a blood stain comes out or stays in. Get those right and most accidents are recoverable.